*NOSEQ
IPRINST
INSTALLATION PARAMETER ENTRIES.
USE + KEY TO SEE NEXT PAGE.
GO. WILL CONTINUE THE LOAD WITHOUT FURTHER DISPLAYS.
THE RIGHT BLANK KEY TOGGLES THE DISPLAY.
CERTAIN INSTALLATION PARAMETERS REFER TO THE JOB SERVICE
CLASS *SC* AND JOB ORIGIN TYPE *OT*.
*SC* MAY BE REPLACED BY THE FOLLOWING -
BC BATCH
CT COMMUNICATION TASK
DI DETACHED INTERACTIVE
I0 INSTALLATION CLASS 0
I1 INSTALLATION CLASS 1
I2 INSTALLATION CLASS 2
I3 INSTALLATION CLASS 3
I4 INSTALLATION CLASS 4
I5 INSTALLATION CLASS 5
I6 INSTALLATION CLASS 6
I7 INSTALLATION CLASS 7
I8 INSTALLATION CLASS 8
MA MAINTENANCE
NS NETWORK SUPERVISOR
RB REMOTE BATCH
SS SUBSYSTEM
SY SYSTEM
TS INTERACTIVE
*OT* MAY BE REPLACED BY THE FOLLOWING -
BC BATCH
IA INTERACTIVE
RB REMOTE BATCH
SY SYSTEM
CLASS=OT,ALL.
CLASS=OT,NUL.
CLASS=OT,S1,S2,...,SN.
SET THE SERVICE CLASSES THAT WILL BE ALLOWED FOR THE
ORIGIN TYPE *OT*. ANY ORIGIN TYPE MAY BE SELECTED
EXCEPT *SY*.
ALL = SET ALL SERVICE CLASSES EXCEPT *SS*
NUL = CLEAR ALL SERVICE CLASSES
SN = ANY SERVICE CLASS (*SC*) EXCEPT *SS*
COMLIB,UN,FM.
ADD AN ENTRY TO THE COMMON LIBRARIES TABLE FOR
FAMILY NAME *FM* AND USER NAME *UN*.
COMLIB,UN,FM,D.
DELETE THE ENTRY FROM THE COMMON LIBRARIES TABLE FOR
FAMILY NAME *FM* AND USER NAME *UN*.
CPM,S1=X1,S2=X2.
ALTER CP MULTIPLIER TYPE *SN*.
SN = 0 OR 1
XN = 1 - 45B (INDEX TO VALUE)
CPTT=NNNN.
SET CPU TRANSFER THRESHOLD FOR INDIRECT FILES TO *NNNN*.
CPU TRANSFER IS DISABLED IF *NNNN* = 0.
NNNN = 0-7777B (SECTOR COUNT).
CSM=CC.
SET THE OPERATING SYSTEM CHARACTER SET MODE.
CC = 63 - 63 CHARACTER SET
= 64 - 64 CHARACTER SET
DEBUG.
TOGGLES CONSOLE DEBUG STATUS.
DELAY,T1XXX,T2XXX,...,TNXXX.
SET SCAN VALUE *TN* = XXX.
TN = AR - PP AUTO RECALL DELAY (MILLISECONDS)
CR - CPU PROGRAM RECALL DELAY (MILLISECONDS)
JS - JOB SCHEDULER DELAY (SECONDS)
JQ - QFT/EJT SCHEDULING DELAY (2**JQ SECONDS)
MP - MEMORY PAD FOR *RSTM* (100B WORD BLOCKS)
DFPT=DTN.
SET SYSTEM DEFAULT REMOVABLE PACK TYPE = DTN.
DT = MASS STORAGE DEVICE TYPE.
N = NUMBER OF SPINDLES IN DEVICE (1 - 8).
DSD,X,CCC-CCC
SET INITIAL KEYBOARD COMMAND(S) = CCC-CCC IF DEADSTART
LEVEL X IS SELECTED.
X = 0-2.
DISABLE,OP.
DISABLE,SYS,CP.
ENABLE,OP.
ENABLE,SYS,CP.
ENABLE OR DISABLE A SUBSYSTEM *SYS* OR AN OPTION *OP*.
CP = CONTROL POINT WHERE SUBSYSTEM WILL RESIDE.
-N TO SPECIFY CP RELATIVE TO THE SYSTEM CP.
OP = ONE OF THE FOLLOWING OPTIONS
ACS TAPE PF STAGING PRIVILEGED ANALYST MODE
AUTORESTART PRIVILEGED RDF
CARTRIDGE PF STAGING PROBE
DDP ROLLOUT PATH REMOVABLE PACKS
DISK VALIDATION RESIDENT RDF
ENGR SCP
EXTENDED STACK PURGING SCRSIM
FLEXIBLE PARTITIONS SECONDARY USER COMMANDS
FORCED FORMATTING SPINDOWN
LOGGING SUBCP
MASTER MSE SYSTEM DEBUG
MASTER MSS TAPE PF STAGING
MEMORY CLEARING TMS
MS VALIDATION TRACE
PF VALIDATION USER EXTENDED MEMORY
SYS = ONE OF THE FOLLOWING SUBSYSTEMS
ATF - AUTOMATED TAPE FACILITY
BIO - BATCHIO
CDC - CYBER DATABASE CONTROL SYSTEM
IAF - INTERACTIVE FACILITY
MAG - MAGNET
MAP - MAP III
MCS - MESSAGE CONTROL SYSTEM
MSS - MASS STORAGE SUBSYSTEM
NAM - NETWORK ACCESS METHOD
NJF - NETWORK JOB ENTRY FACILITY
RBF - REMOTE BATCH FACILITY
RDF - REMOTE DIAGNOSTIC FACILITY
RHF - REMOTE HOST FACILITY
SMF - SCREEN MANAGEMENT FACILITY
SSF - SCOPE STATION FACILITY
STM - STIMULATOR
TAF - TRANSACTION FACILITY
TLF - TIELINE FACILITY
EI=E1,E2,...,EN.
SPECIFIES ACCEPTABLE EI (ENVIRONMENTAL INTERFACE)
REVISION LEVELS.
EN = 2 CHARACTER EI REVISION LEVEL
= NULL, NO EI REVISION LEVEL VERIFICATION PERFORMED
KEYPM=CC.
SET SYSTEM KEYPUNCH MODE.
CC = 26 - O26 KEYPUNCH MODE
29 - O29 KEYPUNCH MODE
LOCK.
SETS CONSOLE LOCK STATUS.
MICRO=M1,M2,...,MN.
SPECIFIES ACCEPTABLE MICROCODE NAMES.
MN = 7 CHARACTER MICROCODE NAME
NAMIAF=NC.
SET THE NUMBER (*NC*) OF NETWORK TERMINALS.
OQSH=LVL.
SET THE OUTPUT QUEUE SPECIAL HANDLING LEVEL.
LVL = ACCESS LEVEL NAME
PCLASS=S1,S2,...,S7.
SET THE SERVICE CLASS ASSOCIATED WITH EACH PRIORITY LEVEL.
SN = ANY SERVICE CLASS (*SC*) EXCEPT *SS*
QUEUE,SC,QT,Q1XXX,Q2XXX,...,QNXXX.
SET QUEUE PRIORITIES *QN* = XXXX ASSOCIATED WITH
QUEUE *QT* FOR SERVICE CLASS *SC*.
QT = EX - EXECUTING QN = IL - ORIGINAL PRIORITY
IN - INPUT IP - INITIAL PRIORITY
OT - OUTPUT LP - LOWER BOUND FOR PRIORITY
UP - UPPER BOUND FOR PRIORITY
WF - WEIGHTING FACTOR
SECCATS=C1,C2,...,CN.
SET THE SECURITY ACCESS CATEGORIES THAT WILL BE ALLOWED IN
A SECURE SYSTEM.
CN = ACCESS CATEGORY NAME, *ALL* OR *NUL*
ALL - ENABLE ALL ACCESS CATEGORIES
NUL - DISABLE ALL ACCESS CATEGORIES
SECURES,OT,LA=LLVL,UA=ULVL.
SET THE ACCESS LEVEL LIMITS FOR AN ORIGIN TYPE *OT*. IF
ORIGIN TYPE IS *SY*, SET THE ACCESS LIMITS FOR THE SYSTEM.
LLVL = ACCESS LEVEL NAME FOR THE LOWER LIMIT
ULVL = ACCESS LEVEL NAME FOR THE UPPER LIMIT
SERVICE,SC,P1XXX,P2XXX,...,PNXXX.
SET JOB SERVICE PARAMETERS *PN* = XXXX, FOR
SERVICE CLASS *SC*.
PN = AM MAXIMUM FL/100B FOR ALL JOBS
CM CENTRAL MEMORY TIME SLICE (SECONDS)
CP CONTROL POINT TIME SLICE PRIORITY
CS CUMULATIVE INDIRECT ACCESS FILE SIZE
CT CONTROL POINT TIME SLICE (SECONDS)
DS INDIVIDUAL DIRECT ACCESS FILE SIZE
DT SERVICE CLASS TO ASSIGN ON A DETACH
EM MAXIMUM XM FL/*UEBS* FOR ALL JOBS
FC NUMBER OF PERMANENT FILES ALLOWED
FL MAXIMUM FL/100B FOR ANY JOB
FS INDIVIDUAL INDIRECT ACCESS FILE SIZE
NJ MAXIMUM NUMBER OF JOBS
PR CPU PRIORITY
RS RECALL CPU SLICE (MILLISECONDS)
SE CPU SLICE EXTENSION (MILLISECONDS)
TD SUSPENSION TIMEOUT DELAY
TP INITIAL PRIORITY FOR ON LINE JOBS
US UNEXTENDED CPU SLICE (MILLISECONDS)
SPC,C1=LLL1,C2=LLL2.
SET ASSUMED PRINT PAGE CHARGE (LINES PER PAGE).
CN = 6 - 6 LINES PER INCH 8 - 8 LINES PER INCH
LLLN = 20B-377B - LINES CHARGED PER PRINT PAGE
SPD=C.
SET ASSUMED PRINT DENSITY ACCORDING TO *C*.
C = 6 - 6 LINES PER INCH 8 - 8 LINES PER INCH
SPL=NNN.
SET ASSUMED PAGE LENGTH ACCORDING TO *NNN*.
NNN = 20B-377B - LINES PER PAGE
SPW=NNN.
SET ASSUMED PAGE WIDTH ACCORDING TO *NNN*.
NNN = 50B-210B - PAGE WIDTH
SRST=NNNN.
SET SECONDARY ROLLOUT SECTOR THRESHOLD TO *NNNN*.
NNNN = 0-7777B - SECTOR COUNT
TCVM=CC.
SET ASSUMED MAGNETIC TAPE CONVERSION MODE.
CC = AS - ASCII NINE-TRACK CONVERSION
EB - EBCDIC NINE-TRACK CONVERSION
US - ANSI (USASI) NINE-TRACK CONVERSION
TDEN=CC.
SET ASSUMED TAPE DENSITY ACCORDING TO *CC*.
TWO ENTRIES MAY BE MADE, ONE FOR MT AND ONE FOR NT.
CC = LO - 200 CPI (MT) HI - 556 CPI (MT)
HD - 800 CPI (NT) HY - 800 CPI (MT)
PE - 1600 CPI (NT) GE - 6250 CPI (NT)
TDTY=CC.
SET ASSUMED TAPE DEVICE TYPE ACCORDING TO *CC*.
CC = AT - ACS CARTRIDGE TAPE
CT - CTS CARTRIDGE TAPE
MT - SEVEN TRACK TAPE
NT - NINE TRACK TAPE
UNLOCK.
SETS CONSOLE UNLOCK STATUS.
VEBL=NNNN.
SET MAXIMUM NUMBER OF TIMES EXCHANGE TO NOS/VE
WILL BE BYPASSED DUE TO PENDING PP EXCHANGES.
NNNN=0-7777B. DEFAULT IS 0.
*WEOR
*WEOR